A basic lake pigment is pretty easy to make. Some lake pigments are more complex – there’s a reason madder lake took a while to catch on, historically – but most of them are easy as pie. It was noted recently in a comment that there is a dearth of comprehensible recipes online, and it’s true. It took me a bit of searching to figure out what things like “base,” “thrown down,” “precipitated onto,” and so on actually mean. But here is the basic process in all its simplicity. Let’s go:
First, what you’ll need. You’ll need alum, for starters – that’s potassium aluminum sulfate. This is the basic material that’s going to grab onto the dye color, just as it does when used as a mordant in fabric dyeing. You used to be able to get the stuff in the spice aisles of grocery stores, and apparently in some parts of the country you still can (it’s used in pickling cucumbers). I purchased mine from a dye shop. Also, you’ll need some kind of alkali to precipitate the alum (turn it into an insoluble powder). Some possibilities are potash (potassium carbonate), washing soda (sodium carbonate) or chalk (calcium carbonate). I use washing soda most often. You can get it from dye shops as well; but for a better deal grab a big container at Home Depot or Lowe’s in the pool section. On the right are these two items.
You’ll need the dyestuff itself. It’s worth noting here that not all dyes will grab onto alum to form a lake pigment; but if you’ve done a little research, you’ll have some idea at least of some of the ones used in the past. Here I’ll use some ripe buckthorn berries. These were most often inspissated to make the watercolor sap green; but the dye from them will make a lake pigment.
Equipment you’ll need: a pot and something to heat it with. On the right you see me heating up the berries in water on the stove. Some dyes, such as carmine, need to be boiled; for others, such as madder, boiling can ruin the color. Research and/or experiment. Other stuff: a funnel, some coffee filters and two jars of some sort (preserving jars work the best, because you don’t have to worry about pouring hot water into them). I usually have various jars around, so I can pour back and forth as needed. You’ll also need some distilled water – this is what should be used whenever the recipe calls for water. A mortar and pestle. And: a turkey baster. No, really.
Once your dye is extracted from the dyestuff, filter it, using the funnel and a coffee filter, over one of your jars. You need to get all the gunk out of there. Now that you’ve got some extracted and filtered dye, the magic can begin. Dissolve some alum in water on the stove (a pic of this can be seen here), then pour the warm alum solution into the dye jar. With some dyes, such as weld, this will immediately bring out the color; with others, you won’t see any difference.
Now, do the same thing with the alkali (be a little careful with potash or washing soda – these are alkaline enough to cause a burn, make sure to keep the stuff out of your eyes): dissolve some in water on the stove, then pour some of the solution into the dye. Right away you should get a fizzing reaction as the alum encounters the alkali: as the alkali precipitates the alum, it releases carbon dioxide (or something like that). How much of each, alum and alkali, should be used? Well, it’ll be different for each dye and each recipe. As a general thing it’s better to add too little than to add too much, as more can always be added later.
Let the jar sit – sometimes for a few hours, sometimes overnight – and the precipitate will eventually settle to the bottom. Now it should be washed a few times. Take your turkey baster (told ya) and siphon off the clear water on top, as much of it as you can without losing too much pigment. Then fill the jar back up with water and allow it to settle again. Do this as many times as it takes for the clear water to be colorless (or as near to that as your patience and water supply can handle!).
Once the water is colorless to your satisfaction, siphon it off one last time, and then you’ll filter the precipitate through the funnel and another coffee filter, into your other jar. The pigment will usually clog the filter, so you’ll need some patience for this: fill up the funnel, then go do something else for a while as it slowly drains, then come back and fill it up again, etc. If you’re making a larger batch of lake you may need more than one filter. Remove the filter containing lake and lay it flat on a surface – I use plates with paper towels, but bricks are supposed to work nicely – and give it a couple of days to dry (but don’t put it in the sun – these are fugitive colors here!). It will probably shrink in volume quite a bit as it loses moisture. Once the lake is completely dry, you can grind it up, thoroughly, using a mortar and pestle.
Now you have your pigment – mull it into linseed oil or gum arabic and give it a go! There’s very little more satisfying than creating a painting with your own pigments and paints. Don’t forget to keep good notes on your process – and feel free to post any questions or comments below.
Tags: buckthorn, lake pigment recipe, lake pigments, natural pigments, Pigments
This entry was posted on January 10, 2011 at 12:07 am and is filed under All, Art materials, Paint making, Pigments. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.